| |
HOW TO INSTALL WOVEN WOOD SHADES
Congratulations on your purchase. Your shade has been custom made to your specifications and is one of the finest window treatments available. Before you unwrap your blinds, please take a few moments to read these instructions. With careful installation and periodic cleaning your shade will provide you with many years of trouble free service.
Your shade includes the following:
- Two installation brackets
- Mounting screws
- Auxiliary Support brackets if your blind requires them
To install your shade you will need the following tools:
- Pencil
- Screwdriver with medium size blade
- Drill
- 7/64" drill bit, or a hammer and finishing nail
- Scissors
- Level(optional)
- 1/16" drill bit
SUGGESTED FASTENER GUIDE
Anchors(not supplied)
Plastic or lead anchor insert.
Plastic anchor insert for lightweight blind only, in drywall, paneling, etc.
Hollow Wall Anchors(not supplied)
Hollow wall anchors for heavy blinds
 |
Hollow wall toggle bolt for heavy blinds.
|
 |
INSTALLATION & OPERATING INSTRUCTIONS WITH WING NUT BRACKETS
Roman & Roll-up Shades
Your woven wood shade is custom made using the finest materials available. Each shade includes all necessary installation hardware and has been checked for operation and alignment. The following instructions are for the three most common installation types.
Inside Hang(ceiling mounted)- Shade is measured and assembled to fit inside the window casement with mounting brackets that is installed to the top casing with screws placed opposite corners. The wing nuts are removed. The screws slide through the slots on the headrail and are secured by a wing nuts.
|
  |
Outside Hang (ceiling mounted)- Shade is measured and assembled to overlap the window casing. The mounting brackets are then installed to the ceiling by means of screws or toggle bolts placed at opposite corners. Remove wing nuts. The screws slide through the headrail slots and are secured with wing nuts.
|
 |
Outside Hang (wall mounted)- Shade is measured and assembled to overlap the window casing. The mounting brackets are then installed to the wall by means of screws or toggle bolts placed at opposite corners. Remove wing nuts. The screws slide through the headrail slots and are secured with wing nuts.
|
  |
OPERATING INSTRUCTION
Woven Shade Operation & Adjustment
Yarn and wood used on these fabrics have been specially selected. The wood slats retain the grain texture and irregularities inherent in natural wood of this type. The selection of pattern and yarns combines this natural wood with the most contemporary colors for a truly unique window fabric
Shade Operation
Both Roman & Roll-Up shades have the same basic hardware and operating procedure. Cords, whether installed on the left or right side have the same locking mechanism. (See illustration A). To raise the shade merely pull on the cord and release the cord when i has reached its desired height. To lower the shade, pull the cord to the center of the shade with a slight tug. Then keep tension on the cord at that angle slowly let the cord go up, thus lowering the shade. if the shade should bind, check the cord alignment over the pulley (under valance).
|
 |
Shade Adjustment & Alignment
Your shade has been carefully inspected and adjusted by the factory, but minor adjustments may be necessary once it has been installed. The yarns in your woven shades are flexible enough to permit minor adjustment horizontally and vertically for proper alignment on your window. If the bottom of your shade becomes uneven, merely pull down on either side to stretch the yarn and align the shade.
If your shade doesn't lie flat against the wall or window, roll the shade tightly from the bottom and twist roll (illustration B) clockwise on one side, counter clockwise on the other, and this will align the yarn and slats. Should a strand of yarn slip off the edge of the shade, remove the strand from top to bottom - this will in no way affect the strength of the shade
|
 |
Shade Maintenance
Clean by Vacuuming.
|
|
|
| |
 |
 |
 |
| |
Home |
FAQ |
Contact Us |
Company Policies |
How to Measure |
Privacy Policy |
How to Install |
About Us |
My Cart
|
|
| |
| 1631 Rock Springs Rd. Apopka, FL 32712 (407) 462 - 7750
sales@gatorblindsstore.com |
© 2008 www.gatorblindsonline.com & Gator Blinds® Orlando Shutters - Draperies
Indoor shutter choices for your windows include Vinyl Interior Shutters and Poly shutters, wood shutters include Bass wood shutters, Hardwood shutters, Faux wood shutters, Poly wood shutters and California Wood. Composite or composite wood shutters along with fiberglass and PVC composite shutters are another choice we offer for your windows. Inside shutters, house shutters and window shutters are available at Gator Blinds® along with standard and custom louvers or windows. Styles include louver shutters, raised panels, flat panel shutters, Interior shutters. Some of the shutters we sell at a discount are custom size shutters along with the custom shutters for your home. Window shutter hardware choices include shutter stays also known as L hinges, strap hinges and hinge. Other interior shutter hardware you may need is: shutter screws. Choose Café shutters or traditional shutter for interior shutters. Buy your top quality interior shutter online at a discount at Gator Blinds® Shutter Company and get free shipping on most orders over $500, continental US only and some products are excluded.
LINK PAGE
|
|
|
 |
 |
 |
|
|
|
|
 |
|
|
